ANCEL DS100 Engine/ABS/SRS Airbag/Transmission Diagnosis Tool
Engine System:
The diagnostic tool can help detect the engine ignition, fuel injection, air and fuel ratio, and exhaust emission conditions
in Engine system to enhance vehicle performance, save energy and reduce exhaust emission.
Transmission:
It makes great sense in the safe driving when your car is slipping or difficult to shift. This diagnostic scanner can figure
the problems out via reading codes in the Transmission system, or check the health status via live data viewing.
ABS System:
Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to
retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you.
SRS Airbag System:
SRS, safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this
diagnostic device can detect every electronic parameter to check its health status
7 Special Functions
1. Oil Lamp Reset Service
perform reset for a new calculation of Engine Oil Life system once changed the oil.
2. SAS Steering Angel Sensor Reset
Reset the steering angle to zero to keep the car running straight.
3. Electronic Throttle Position Reset
enables you to make initial settings to throttle actuators and returns the learned values stored on ECU to the default
state. Doing so can accurately control the actions of regulating throttle (or idle engine) to adjust the amount of air intake
4. D.P.F regeneration may be performed in the following cases:
1. The exhaust back pressure sensor is replaced.
2. The
PM trap is removed or replaced.
3. The fuel additive nozzle is removed or replaced.
4. The catalytic oxidizer is removed
or replaced.
5. The DPF regeneration MIL is on and maintenance is performed.
6. The DPF regeneration control module
is replaced.
5. When would you use ABS Bleeding? Exhausting air from the ABS system is important for maintaining proper brake
performance.
6. Battery matching must be performed in the following cases:
1. Main battery is replaced.
2. Battery monitoring sensor
is replaced.
7.When SAS Reset will be used: After replacing the steering angle position sensor, steering mechanical parts (such as
steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering the
car body, use Ancel DS100 to reset the steering angle.
PLEASE NOTE: Functions may vary from vehicle make and model
Full OBD2 detection, better detection of car engine system!
This scanner supports all 10 test modes for OBD-II cars which are great for daily repair work. The table below describes
the purpose of each mode of operation:
1. Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
2. Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
3. Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame
data.
4. I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly
and are ready for inspection and maintenance testing.
5. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform)
display.
6. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the
time the emission-related fault occurs.
7. O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests
from the vehicle’s on-board computer.
8. On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.
9. Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID)
and CVN (Calibration verification number), etc.
10. Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their
operability.
Please Note: Electronics And Software Are Not Refundable
(Please Read The Ad Carefully Before Purchasing)
Payment Policy
PAYMENTS:
Orders must be fully paid before any stock will leave the premises
Delivery Policy
DELIVERY Policy:
• Shipment Processing Time, All Orders Are Processed Within 2-3 Business Days.
• Orders Are Not Shipped Or Delivered On Weekends Or Holidays.
• You will be notified via email or telephone if Shipments May Be Delayed By A Few Days.
• Normal Shipping Time Takes 3 – 12 Business Days depending on stock availibilty.
• Shipping Rates & Delivery Estimates, Shipping Charges For Your Order Will Be Calculated And Displayed At Checkout.
• We Only Ship Inside Of South Africa, Should You Want To Place An Order But You Stay In Any Other Country, You’ll Have To Arrange Your Own Shipping Method, Or You Can Kindly Speak To Us For a shipping quote Assistance.
Shipment Confirmation & Order Tracking:
• You Will Receive A Shipment Confirmation Email Once Your Order Has Shipped Containing Your Tracking Number(S).
• The Tracking Number Will Be Active Within 24 Hours.
• Delivery Delays Can Occasionally Occur, When Handed Over To The Courier It Will Be Out Of Our Control.
Damages:
• Diatools Is Not Liable For Any Products Damaged Or Lost During Shipping. If You Received Your Order Damaged, Please Contact The Shipment Carrier To File A Claim.
Refund Policy
REFUNDS:
There Are No Refunds On Electrical Goods.
Refunds Will Only Be Done Once Authorized By The Manufacturer And Not The Seller Namely Diatools.
If The Manufacturer Agrees With A Refund, Then All Expenses (Namely: Shipping And Customs, Etc.) Including A Handling Fee Of 20% Will Be Charged.