Ancel DS300 Bi-Drectional Full System Diagnostic Tool & 28+ Special Functions

ANCEL DS300 Bi-Directional Full System Diagnostic Tool & 28+ Special Functions

To diagnose car comprehensively, ANCEL DS300 scanner can read DTCs and data streams, perform active test, Coding for ALL systems. For instance: Engines/Auto Transmission/Airbags/Immobilizer/Key Coding

ABS/Cruise Control/Instruments/ Self Leveling Suspension systems/Seats

Doors/Gateway/Steering Angle/Air Suspension/Body Systems/Electronic Power Steering & Motor Assisted

Power Steering/Tire Pressure/Rain Sensors/4WD System/Stabilizer/Intelligent Parking Assist

Door Motors/Audio Systems/Air Conditioning/Tiptronic/Anti-Theft/Soft Top/Headlamp Leveling

Central Locking/Automatic Clutch/ DPF Reset/Electric Windows/Plip Programming/Heated Rear Window

Xenon Headlights/Wash Wipe/Fuel Burning Heater/Transfer Box/Seat Memory/Oil Life Service Reset/Sliding Doors

Electronic Throttle/Navigation System/Rollover Sensor/Cruise Control/ Multi-Function Steering Wheel Aux Heating/Electronic Parking Brake/Clutch Electronics, ....etc.

PLEASE NOTE: Functions may vary from vehicle make and model

Bi-Directional Control (Actuation Test):

ANCEL DS300 scan tool with full-featured bi-directional control ability can actuate solenoids and actuators for active testing, send commands to many systems/components to test their working status, without using the vehicle controls. Turn on the fuel pump, radiator fan, modulate the throttle, open/close windows, operate mirrors, turn on interior & exterior lights, sound horn, test door lock actuators etc.

28 Special Functions:

Oil Reset:

The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

Elec. Throttle Adaption:

Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.

Steering Angle Reset:

To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.

Battery Matching:

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

ABS Bleeding:

When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

Break-pad Reset:

lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.

DPF Regeneration:

DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.

Gear Learning:

After the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed.

IMMO Service:

To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

Injector Coding:

Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity.

TPMS Reset:

Note: Co-operate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions

Suspension Matching:

This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration.

AFS Reset:

This feature is used to initialize the adaptive headlamp system.

A/T Learning:

This function can complete the gearbox self-learning to improve gear shifting quality.

Sunroof Initialization:

This function can set the sunroof lock off, closed when it rains, sliding /tilting sunroof memory function, temperature threshold outside the car etc.

EGR Adaption:

This function is used to learn the EGR valve after it is cleaned or replaced.

Airbag Reset:

This function resets the airbag data to clear the airbag collision fault indicator.

Transport Mode:

ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this t ime, the transport mode needs to be deactivated to restore the vehicle to normal.

A/F Reset:

This function is applied to set or learn Air/Fuel ratio parameters.

Stop/Start Reset:

This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware).

NOx Sensor Reset:

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu.

AdBlue Reset (Diesel Engine Exhaust Gas Filter):

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

Seat Calibration:

This function is applied to match the seats with memory function that are replaced and repaired.

Coolant Bleeding:

Use this function to activate the electronic water pump before venting the cooling system.

Tire Reset:

This function is used to set the size parameters of the modified or replaced tire.

Windows Calibration:

This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window.

Language Change:

This function is used to change the system language of the vehicle central control panel.

More convenient features to help you

Auto read VIN number: It can read VIN information automatically when you connect Car

Quickly Print Diagnostic Report: Print the diagnostic report of your car at any time way print: Transfer the diagnostic report to the computer via USB, and then print it

Diagnostic Feedback: When you encounter unsolvable problems or diagnostic software bugs during diagnosis, you can revert the most recent 20 test records to ANCEL Team. When we receive your feedback, we will analyze and troubleshoot it in a timely manner, to improve the quality of our products and user experience.(please contact with us after leaving feedback, thank you)

4 in One Graphic Data Stream(4 Data Graphs shows in the Same Screen)

1.Combine: Displayed in graph merge status for data comparison.

2.Value: Displayed the parameters in values and shown in list format.

3.Customize: Customize the data stream option to be viewed. Tap the button, a pull-down list of the data stream items appears on the screen. Select the desired items (max4 items), and then screen will display the waveforms corresponding to these items immediately. If need to remove any items, just deselect them.

Please Note: Electronics And Software Are Not Refundable (Please Read The Ad Carefully Before Purchasing)

Payment Policy

PAYMENTS:
Orders must be fully paid before any stock will leave the premises

Delivery Policy

DELIVERY Policy:
• Shipment Processing Time, All Orders Are Processed Within 2-3 Business Days.
• Orders Are Not Shipped Or Delivered On Weekends Or Holidays.
• You will be notified via email or telephone if Shipments May Be Delayed By A Few Days.
• Normal Shipping Time Takes 3 – 12 Business Days depending on stock availibilty.
• Shipping Rates & Delivery Estimates, Shipping Charges For Your Order Will Be Calculated And Displayed At Checkout.
• We Only Ship Inside Of South Africa, Should You Want To Place An Order But You Stay In Any Other Country, You’ll Have To Arrange Your Own Shipping Method, Or You Can Kindly Speak To Us For a shipping quote Assistance.
Shipment Confirmation & Order Tracking:
• You Will Receive A Shipment Confirmation Email Once Your Order Has Shipped Containing Your Tracking Number(S).
• The Tracking Number Will Be Active Within 24 Hours.
• Delivery Delays Can Occasionally Occur, When Handed Over To The Courier It Will Be Out Of Our Control.
Damages:
• Diatools Is Not Liable For Any Products Damaged Or Lost During Shipping. If You Received Your Order Damaged, Please Contact The Shipment Carrier To File A Claim.

Refund Policy

REFUNDS:
There Are No Refunds On Electrical Goods.
Refunds Will Only Be Done Once Authorized By The Manufacturer And Not The Seller Namely Diatools.
If The Manufacturer Agrees With A Refund, Then All Expenses (Namely: Shipping And Customs, Etc.) Including A Handling Fee Of 20% Will Be Charged.